tantalum solid electrolytic capacitors/tes design, specifications are subject to change without notice. ask factory for technical specifications before purchase and/or u se. whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. ? ee31 ? ta . tes tes series: -55 to 125 c 4 to 16 v .dc 0.47 to 15 f 20 % (120hz/20 c) n dimensions in mm (not to scale) w2 p ( + ) ( - ) w2 l h w 1 n marking p l size z n case size surface mount type n features n specifications category temp. range rated w.v. range nominal cap. range capacitance tolerance dc leakage current moisture resistance endurance capacitance change tan d . dc leakage current 10% of initial measured value < initial specified value < 125 % of initial specified value please see the attached standard products list the following limits. after 2000 hours application of rated dc working voltage at 85 c or derated voltage at resistance to soldering heat capacitance change tan d. dc leakage current 10% of initial measured value < initial specified value, miniatured size : < 150% of initial specified value. < initial specified value 4. other rating upon request (voltage, capacitance, tolerance) tan d low profile height: h=1.2mm max. l0.2 w10.2 w20.1 h max. p 1.25 0.9 1.2 0.50.2 eia code 2012 size code z 2.0 capacitance code 4 6.3 10 16 g j a c w.v. code w.v. (v) code polarity bar (+ side) w.v.code cap. code (ex.) je : 6.3v 1.5f japan china 4(0g) 6.3(0j) 10(1a) 16(1c) w.v.(v.d c) cap(f) standard miniature standard miniature standard miniature standard miniature z z z z z z z z z z z z z z z z z z 0.47 (474) 0.68 (684) 1.0 (105) 1.5 (155) 2.2 (225) 3.3 (335) 4.7 (475) 6.8 (685) 10 (106) 15 (156) 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 s w a e j n s w a e capacitance(f) 1st code i < 0.01cv or 0.5 (a) after 2 m i n utes application of r ated w o r king v oltage at 20 c (whiche v er is greater) w.v. and capacitance code. n o t e : 1 . ( ) i n d i c a tes 2. when selecting w . v . refer to page 20. 3. w e recommend current sizes shown in the above table for new design, but conventional case size is available on request. the capacitor shall withstand dipping into solder for 51 seconds at 260 5 c after 500 hours e xposure at 40 c and 90 to 95 % r.h. without load, the capacitor shall meet 125 c , the capacitor shall meet the following limits. rev.02/04
tantalum solid electrolytic capacitors/tes design, specifications are subject to change without notice. ask factory for technical specifications before purchase and/or u se. whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. ? ee32 ? n standard products lxwxh (mm) (pcs) (f) (a) l.c case size specification cap. (20%) w.v. part no. min. packaging q'ty taping size code 4 6.3 10 16 tan d (120hz) (20 c) 2.2 2.0x1.25x1.2 z 0.5 0.10 25 ecst0gz225r 3000 3.3 2.0x1.25x1.2 z 0.5 0.15 20 ecst0gz335r 3000 6.8 2.0x1.25x1.2 z 0.5 0.20 20 ecst0gz685r 3000 10 2.0x1.25x1.2 z 0.5 0.20 15 ecst0gz106r 3000 15 2.0x1.25x1.2 z 0.6 0.20 15 ecst0gz156r 3000 1.5 2.0x1.25x1.2 z 0.5 0.10 25 ecs t0jz155r 3000 2.2 2.0x1.25x1.2 z 0.5 0.12 20 ecst0jz225r 3000 4.7 2.0x1.25x1.2 z 0.5 0.20 20 ECST0JZ475R 3000 6.8 2.0x1.25x1.2 z 0.5 0.20 15 ecst0jz685r 3000 10 2.0x1.25x1.2 z 0.7 0.20 15 ecst0jz106r 3000 1 2.0x1.25x1.2 z 0.5 0.10 25 ecst1az105r 3000 1.5 2.0x1.25x1.2 z 0.5 0.12 20 ecst1az155r 3000 2.2 2.0x1.25x1.2 z 0.5 0.20 15 ecst1az225r 3000 3.3 2.0x1.25x1.2 z 0.5 0.20 15 ecst1az335r 3000 4.7 2.0x1.25x1.2 z 0.5 0.20 15 ecst1az475r 3000 0.47 2.0x1.25x1.2 z 0.5 0.10 28 ecst1cz474r 3000 0.68 2.0x1.25x1.2 z 0.5 0.10 25 ecst1cz684r 3000 1 2.0x1.25x1.2 z 0.5 0.20 20 ecst1cz105r 3000 esr (100khz) (20 c) ( w )
|
